SFF200-03CT thru sff200-06ct page: 1 frontier electronics corp. 667 e. cochran street, simi valley, ca 93065 tel: (805) 522-9998 fax: (805) 522-9989 e-mail: frontiersales@frontierusa.com web: http://www.frontierusa.com 20a dual super fast recovery rectifier SFF200-03CT thru sff200-06ct case : ito-220ab( sff200-xx ) , fully insulated package features mechanical data z ultra fast recovery time z case: transfer molded z low forward voltage z terminal: mil-std-202f method 208 z low thermal resistance z polarity: as marked z high current capability z epoxy: ul94v-0 flame retardant molding compound z high voltage z weight 2.05 grams z glass passivated chip junction maximum ratings and electrical characteristics ratings at 25 c ambient temperature unless otherwise specified single phase, half wave, 60 hz, resistive or inductive load. for capacitive load, derate current by 20%. ratings symbol SFF200-03CT sff200- 04ct sff200-05ct sff200-06ct units maximum recurrent peak reverse voltage v rrm 300 400 500 600 v maximum rms voltage v rms 210 280 350 420 v maximum dc blocking voltage v dc 300 400 500 600 v maximum average forward rectified current see fig.1 i o 20.0 a peak forward surge current, 8.3ms single half sine-wave superimposed on rated load i fsm 250 a typical junction capacitance (note 1) c j 65 pf typical thermal resistance (note 2) r jc 2.2 c /w storage temperature range t stg - 55 to + 150 c operating temperature range t op - 55 to + 150 c electrical characteristics (a t t a =25 c unless otherwise noted) characteristics symbol SFF200-03CT sff200-04ct sff200-05ct sff200-06ct units maximum forward voltage at 10a per leg v f 1.30 1.70 v maximum dc reverse current at ta=25 c i r 10 a maximum dc reverse current at ta=100 c i r 100 a maximum reverse recovery time (note 3) t rr 35 ns notes : 1. measured at 1 mhz and applie d reverse voltage 0f 4.0 volts 2. thermal resistance junction to case per leg mounted on heat sink 3. reverse recovery test conditions: i f =0.5a, i r =1.0a, i rr =0.25a millimeters min max b c d e f g h i j k l m o 9.72 6.30 14.50 13.00 - 2.41 - - - - 2.5 - 10.27 6.90 15.50 13.80 4.1 2.67 1.52 0.9 4.8 3.1 2.9 0.8 ? 3.4 c f h b d g e 1 2 3 o i pi n 1 pin 3 pin 2 case j m k l
SFF200-03CT thru sff200-06ct page: 2 ratings and characteristic curve SFF200-03CT thru sff200-06ct +0.5a 0 -0.25a -1.0a trr 1c m set time base for 10/20 ns/cm fig. 1 -test circuit diagram and reverse recovery time characteristic pulse generator ( note 2 ) (+) 25 v dc (approx) (-) d.u.t. 1 non inductive oscilloscope ( note 1 ) 50 no inductive 10 no inductive (-) (+) note: 1. rise time=7ns max. input impedance=1 mohms 22pf 2. rise time =10 ns max. source impedance=50 ohms fig. 4 -typical reverse characteristics 20 40 60 80 100 120 140 percent of rated peak reverse voltage (%) 1000 100 10 1 0.1 t j =25 o c t j =80 o c t j =125 o c instantaneous reverse current (ua) fig. 3 -typical instantaneous forward characteristics 0 .2 .4 .6 .8 1.0 1.2 1.4 1.6 1.8 instantaneous forward voltage (v) 100 10 1.0 .1 .01 instantaneous forward current (a) SFF200-03CT~04ct sff200-05ct~06ct average forward current (a) 20 16 12 8 4 0 25 50 75 100 125 150 175 case temperature ( o c) fig. 2 -typical forward current derating curve single phase half wave 60hz resistive or inductive load fig. 5 -typical junction capacitance .1 .2 .4 1.0 2 4 10 20 40 100 reverse voltage (v) 2000 1000 400 200 100 60 40 20 10 junction capacitance (pf) t j =25 o c
|
